PLUMBING 101: A GUIDE TO BATHTUB INSTALLATION

Plumbing 101: A Guide to Bathtub Installation

Plumbing 101: A Guide to Bathtub Installation

Blog Article

Schedule Today

We've found the article on How to Install a Bathtub Yourself directly below on the internet and concluded it made good sense to share it with you over here.


How to Install a Bathtub
Setting up a bathtub isn't exactly rocket science, but it does call for solid plumbing, carpentry, and often, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately difficult job. If the old tub is conveniently easily accessible, the task can move speedily; if you need to open a wall to eliminate the old tub and position the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's skills, although you will need an assistant to vacate the old bathtub and also set in the new one. Ensure you have actually certified on your own for the work and also fit trying it. As opposed to working with a professional to take over a halfway-completed task, it is far better to consider employing one before you begin. Chances are you may need a specialist plumber to make tube links.
This short article will assist you install a brand-new bathtub in your bathroom if you have actually currently acquired a brand-new bathtub and do not need to alter the arrangement of your previous water supply pipelines.
Your tools and also product list need to comprise the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of eliminating the existing taps can be rather troublesome because of the restricted gain access to that is commonly the situation.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the remaining water that will certainly come from the pipelines. Once the supply pipes have been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
    Prior to proceeding to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, after that you will need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end provides a link to the existing supply pipes.
    If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
    Next, place the tap in the installing opening in the bath/basin ensuring that the washers are in location between the tap as well as the sink. Protect the faucet in place with the producer provided backnut. Once the tap is securely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The former type must be attached to the faucet ends initially, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Installing the Bathtub


    Using both wood boards under its feet, position the bathtub in the required setting. The wooden boards are useful in equally spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
    The following objective is to make sure that the bathtub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bathtub until the level reviews degree.
    To install faucets, fit all-time low of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the same for the various other tap.
    Activate the water supply and inspect all joints as well as brand-new pipework for leaks and tighten them if needed. Fill up the bath tub and likewise examine the overflow electrical outlet and the normal outlet for leakages.
    Ultimately, fix the bath paneling as described in the producer's instruction manual. Tiling and also securing around the bath tub should wait until the bathtub has been used at the very least when as this will settle it into its last placement.

    Planning for the Setup


    Firstly, the sustaining framework provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets device to avoid pressure on the bathtub.
    Fit the flexible tap ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
    Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its final position.

    Tiling Around the Bath tub


    In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a rigid seal, creating the water to pass through the wall surface in between the bath and the tiling, resulting in complications with wetness as well as feasible leaks to the ceiling below.
    You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to permit the movement experienced when the bathtub is in use. The sealer can fracture fairly early if you do not take into account this movement before sealing.
    Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly available on the market. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive and also cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub Yourself

    Do you appreciate reading about Installing A Bathtub? Create feedback below. We will be delighted to hear your thinking about this post. We are looking forward that you visit us again soon. Remember to take the opportunity to share this article if you appreciated it. Kudos for your time. Please come visit our website back soon.


    Try Here

    Report this page